Toa SR-TB4 User Manual download pdf

Printed in Japan

133-01-441-50

Speaker mounting bracket

(component of the SR-TB4)

Hexagon head bolt M5 x 20

(supplied with the SR-TB4)

Remove the 8 attached screws.

Note

The removed screws are not used.

Screw slot

[When facing the speaker toward the left]

Speaker

[Wall mounting dimensions]

180

4-12 x 22

Unit: mm

ø60

Turn the bracket base upside-

down to face the speaker

toward the right.

Bolts and nuts used to fix a

bracket base on a wall are not

included. Use bolts and nuts

that are appropriate for the

construction of wall.

WARNING

Bracket base

(component of the SR-TB4)

Hexagon head bolt M8 x 20

(supplied with the SR-TB4)

Allow the space for

inserting the speaker

mounting bracket.

INSTALLATION MANUAL

WALL TILT BRACKET

SR-TB4

The SR-TB4 is designed to be used exclusively to mount the

SR-S4L or SR-S4S Line Array Speaker on a wall.

It allows the speaker orientation angle to be adjusted to 5° max.

vertically and 20° max. horizontally.

The SR-TB4 is intended for indoor use. Never use it outdoor.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

3. SPECIFICATIONS

• Accessories

Hexagon head bolt M8 x 20 (with washer) ........ 4

Hexagon head bolt M5 x 20 (with washer) ........ 8

Note: The design and specifications are subject to change without

notice for improvement.

Step 1. Install the bracket base on a wall.

Determine the orientation of the bracket base

depending on whether the speaker is to face left or

right.

Step 2. Attach the speaker mounting bracket to the bracket

base.

Horizontal facing angle can be adjusted in the range of

0° to 20°.

2. INSTALLATION

Bracket base

Speaker mounting bracket

Horizontal facing angle: 20°

After the speaker's horizontal orientation has been

determined, fix the speaker mounting bracket to the base.

Note

The speaker's horizontal orientation can be adjusted after

the speaker has been installed.

Step 4. Fix the hexagon head bolts (one each on both sides)

loosely to the position indicated in the figure above.

Step 5. Connect a speaker cable to the speaker.

Step 6. Insert the loosely fitted speaker bolts into the speaker

mounting bracket's screw slots.

Step 7. Fix the hexagon head bolts (3 each on both sides)

loosely to the speaker.

Step 8. Adjust the vertical angle, then securely tighten 8

loosely fitted speaker bolts.

Vertical facing angle can be adjusted in the range of

0° (horizontal) to 5°.

Vertical facing

angle: 5°

Vertical facing angle:

0° (horizontal)

Set for a mark.

• Refer all installation work to the dealer from whom the unit was

purchased. Installation requires extensive technical knowledge

and experience. The speaker may fall off if incorrectly installed,

resulting in possible personal injury.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the speaker falling down and causing personal injury and/or

property damage.

• Owing to the speaker's size and weight, be sure that at least two

persons are available to install the speaker. Failure to do so

could result in personal injury.

• Do not use other methods than specified to mount the bracket.

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the wall's structure

and composition. Failure to do so may cause the speaker to fall,

resulting in material damage and possible personal injury.

•

Tighten each nut and bolt securely. Ensure that the bracket has

no loose joints after installation to prevent accidents that could

result in personal injury.

•

Do not mount the unit in locations exposed to constant vibration.

The mounting bracket can be damaged by excessive vibration,

potentially causing the speaker to fall, which could result in

personal injury.

Indicates a potentially hazardous situation which, if mishandled,

could result in death or serious personal injury.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

•

Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or

property damage.

•

Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the unit that could cause the unit to fall, possibly causing

personal injury.

1Step 3. Remove the attached screws on both sides of the

speaker.

Number of Speakers 1

to be Mounted

Finish Steel plate, white, paint

Dimensions 166 (w) x 247 (h) x 201 (d) mm

(complete assembly)

Weight 3.2 kg

Product Composition Speaker mounting bracket ...... 1,

Bracket base ...... 1

WALL TILT BRACKET 1

Summary of Contents

Page 1 - WALL TILT BRACKET

Printed in Japan133-01-441-50Speaker mounting bracket (component of the SR-TB4)Hexagon head bolt M5 x 20 (supplied with the SR-TB4)Remove the 8 attach

Comments to this Manuals

No comments

Toa SR-TB4 User Manual

Browse online or download User Manual for Acoustics Toa SR-TB4. Toa SR-TB4 User Manual [cs] [pl] [en] [de]

Summary of Contents

Comments to this Manuals

Related products and manuals for Acoustics Toa SR-TB4