Thank you for purchasing TOA's combination camera. Please carefully follow the instructions in thismanual to ensure long, trouble-free use of you
106. Align the positioning mark on the base unit with that on the camera unit.Align the marks4. Perform DIP SW settings on the camera unit.(For de
11NoteWhen mounting the camera unit to the base unit,mount it straight till it is attached to the base unitcorrectly. Mounting it at an angle may caus
129. Tighten 2 camera unit mounting screws.10. Align the positioning mark on the ceiling mounting cover with that on the base unit.Ceiling mounting co
138. MOUNTING THE CAMERA TO A WEAK CEILING PANELUse the optional C-BC511C or C-BC511C-S Ceiling Mounting Cover and the optional C-BC511A CeilingMounti
148.2. Mounting Procedures1. Make a mounting hole of ø140 mm in the ceiling panel.2. Install the anchor bolt for ceiling mounting bracket and anchor b
158. For subsequent procedures, follow the steps 1 – 11 on p. 9 – 12.6. Attach the supplied safety wire to the base unit.7. Attach the safety wire con
169. FLUSH CEILING MOUNTING• Use the optional C-BC511U or C-BC511U-S Flush Ceiling Mounting Bracket.• Flush mounting can be used to reduce the camera&
179.2. Mounting Procedures1. Make a mounting hole of ø230 mm in the ceiling panel.2. Install the anchor bolt for flush ceiling mounting bracket and an
186. Release the lock on the hinged portion of the base unit and run the video, transmission and power cablesextending from the ceiling through the fl
199. Perform steps 3 – 5 on p. 9 – 10.7. Place the flush ceiling mounting bracket in the ceiling behind the ceiling panel by inserting it through them
2TABLE OF CONTENTS1. SAFETY PRECAUTIONS ... 32. GENERAL DESCRIPTION ...
2010. Attach the camera unit to the base unit.Align the positioning mark on the camera unit with that on the flush ceiling mounting bracket. Align the
2110. CEILING SUSPENSIONUse the optional C-BC511P Ceiling Suspension Bracket in combination with the optional C-BC511C or C-BC511C-S Ceiling Mounting
224. Detach footings and saddle bracket on the camera mounting side from the suspension pipe.• Removed saddle brackets and screws are attached to the
235. Attach the suspension pipe (saddle bracket and footing) to the suspension plate.Note: Ensure that the installed suspension pipe faces in the inte
2411. Attach the supplied safety wire to the base unit.Camera directionFootingM4 x 8 machine screw (supplied with the combination camera) 12. Attach r
2513. Attach the safety wire attached to the base unit to the saddle bracket of the suspension pipe.14. Attach the base unit (with footing) to the sus
26Top coverTabTabCamera directionTop cover15. Release the lock on the hinged portion of the base unit and connect the power, video, and signal cables
2711. WALL MOUNTINGUse the optional C-BC511W Wall Mounting Bracket and optional C-BC511C or C-BC511C-S, CeilingMounting Cover.NoteBe sure to use the s
284. Perform steps 11 – 16 on p. 24 – 26.5. Attach the top cover. Insert one top cover's clicks into the other top cover's slots.Mount the t
2912.1. Precautions When Installing the Camera• Avoid install the camera cable in close proximity to other cables of electric products, such as fluore
31. SAFETY PRECAUTIONS• Be sure to read the instructions in this section carefully before use.• Make sure to observe the instructions in this manual a
30NOCOMNCNOCOMNC[ Normal ][ Alarm ]Rated, Maximum permissible voltage: 20 V DC Permissible current limit: 1 AContact useful life: 100,000 times13.3. A
31DIP SW1DIP SW2DIP SW313.4. DIP Switch SettingsNotes• Set the unused DIP switches to the "OFF" position. • If the DIP switches are not set
3213.4.1. Camera Address Setting Switch (DIP Switch 1: No. 1 – 8)Used to set camera address when using the camera in connection with the C-RM500 Remot
33ON123456781173349ON12345678ON12345678ON12345678ON123456782183450ON12345678ON12345678ON12345678ON123456783193551ON12345678ON12345678ON12345678ON12345
34ON1234567865 81 97 113ON12345678ON12345678ON12345678ON1234567866 82 98 114ON12345678ON12345678ON12345678ON1234567867 83 99 115ON12345678ON12345678ON
35ON12345678129 145 161 177ON12345678ON12345678ON12345678ON12345678130 146 162 178ON12345678ON12345678ON12345678ON12345678131 147 163 179ON12345678ON1
36ON12345678193 209 225 241ON12345678ON12345678ON12345678ON12345678194 210 226 242ON12345678ON12345678ON12345678ON12345678195 211 227 243ON12345678ON1
37Combination cameraOutdoor combination cameraMulti-switcherMonitorDedicated remote controller14. SYSTEM EXAMPLES
38C-CC514 NT C-CC514 PL24 V AC, 50/ 60 Hz9 W (normal operation), 19 W max. (1.3 A max.)RS-485 communications system (applicable protocol: Type A, Type
39C-CC564 NT C-CC564 PL24 V AC, 50/ 60 Hz9 W (normal operation), 19 W max. (1.3 A max.)RS-485 communications system (applicable protocol: Type A, Type
4When Installing the Unit• To avoid electric shocks, be sure to switch off the power before power supply wiring work. Failure to do somay result in el
40C-CC574 NT24 V AC, 50/ 60 Hz 9 W (normal operation), 19 W max. (1.3 A max)RS-485 communications system (applicable protocol: Type A, Type B)VBS 1.0
41C-CC574 PL24 V AC, 50/ 60 Hz 9 W (normal operation), 19 W max. (1.3 A max)RS-485 communications system (applicable protocol: Type A, Type B)VBS 1.0
42• AccessoriesSafety wire ... 1Camera mounting screw (machine
133-05-405-9BURL: http://www.toa.jp/
52. GENERAL DESCRIPTIONTOA’s dome-type color cameras combine with a high-speed camera drive that permits one 360-degreehorizontal rotation per second
6• To clean, be sure to first unplug the power plug from the AC outlet, then wipe with a dry cloth. When the unitgets very dirty, use a cloth dampened
7(1) Power supply terminal(2) Video output terminal (VIDEO OUT)(3) Connector (CN1)(4) Connector (CN2) *1(5) Safety wire(6) DIP switch (SW1)(7) DIP swi
8Notes• Mount the camera to a heavy-duty ceiling surface (such as concrete ceiling).• When mounting directly to the ceiling (such as a double ceiling)
97.2. Mounting Procedures1. Mount the base unit to the ceiling.First fix two of the base unit mounting holes as shown below. Since no mounting screws
Comments to this Manuals