INSTALLATION MANUALAPPLIED INSTALLATIONRACK-MOUNTED EMERGENCY PA SYSTEMFS-971 SERIES MODEL NUMBERS : FS-971
10HC24VGNDBUS ( )BUS ( )1EHCJP-0410 front-mounted middle row terminal blockGNDGNDGND GNDGNDGND24 VCHIMEACTIGEM RM PWR112234 5 67 8191011 12IN US
111. Strip the cable sheath 9 mm using the strip gaugeprovided on the side of the terminal block.2. Insert the cable into the terminal block.• Solid c
Under 1200 mOver ø1.2 mmOver ø0.5 mm124. CONNECTION OF REMOTE MICROPHONE RM-1100 (AUX CONTROL TERMINAL)4.1. Notes on Connections The maximum cable dis
134.3. Priority Setting When Multiple RM-1100s Are Connected 4.3.1. Priority setting First-in-first-out priority: Connect the First-in-first-out termi
145. GENERAL BROADCAST AND ATTENUATOR-FREE BROADCAST DURING POWER FAILURE 5.1. How to Make "Power-Failure" General Broadcast and Attenuator-
155.3. Connections 24 VDCJP-0410EP-0510Connection diagram 1Power amplifier panelDigital announcer, etc.Pre-amplifier panelFront-mounted terminal block
16In Connection diagram 2, attenuator-free broadcast can automatically be made using the digitalannouncement machine, etc. when the attenuator-free br
176. CONNECTIONS WHEN MULTIPLE EQUIPMENT RACKS ARE INSTALLED SIDE BY SIDE 6.1. Expansion Control Panel Connections When many expansion control panels
186.3. Expansion Junction Panel Connection when Expanding the DC Power Supply PanelWhen many expansion junction panels are used and they are separatel
196.4. Specifications of Each Cable Set 6004 Yellow3 Orange2 Red14321Model No.Model NameYR-931Cable SetYR-932Cable SetCableYR-931EP-EP PowerExpansion
2TABLE OF CONTENTS1. SUPPLIED MANUALS ... 42.
207. ABOUT THE MULTI-ORIGINATION MATRIX SYSTEM By employing the Input Matrix Panel IM-011, you can provide simultaneous outputs of paging calls orback
217.1. How to Divide the Speaker Lines of the Junction Panel Junction panel's power amplifier terminals can be divided for a group of consecutive
22• Be sure to divide the speaker lines when connecting two or more power amplifier panels to the junctionpanel or expansion junction panel. Failure t
237.2. Input Matrix Panel Connections • Up to eight Input Matrix Panels IM-011 can be connected.• Inputs and outputs must be of full matrix configurat
24[Important] Audio Input 1 is solely intended for emergency broadcast. Be sure to connect Input 1 to the EP-0510'sEmergency/General output.43211
257.3. IM-011 Address Setting 1. Remove the IM-011's two front panel screws to remove the front panel.2. Rotate the address switch with a screwdr
267.5. Connections Note : Connections of both the emergency broadcasting and power supply sections are omitted.Power amplifier panelPower amplifier pa
277.6. IM-011 Connections 7.6.1. Rear view diagrams and block diagrams Notes • Be sure to connect the EP-0510's Emergency/General output to Audio
2823412341234112341234123423411234IM-011 controlEmergency/General outputTo Integrated Control Panel EP-0510Address 0To input source (general-purpose r
297.6.4. Output expansion: 4-input/8-output configuration 23456 78Address 111234Address 0To input sourceTo power amplifier panel inputTo power amplifi
37. ABOUT THE MULTI-ORIGINATION MATRIX SYSTEM ... 207.1. How to Divide the Speaker Lines of the Junction P
301234123456785678910111213 14 15161234123411234123423412341123412341234 56782341234567811234123423412341123412342341234910111211234123423412341123412
31123412345678567819101112 13 14 15 16InputInputTo power amplifier panel inputTo power amplifier panel inputTo power amplifier panel inputTo power amp
327.6.7. Notes on input level settings when increasing the output When increasing output numbers to 8, 12 or 16 outputs by connecting two or more IM-0
33The following figure shows the inputs of both "Address 0" and "Address 1" panels are set for different levelswhen their outputs
Status to Turn Output OnWarning Announcement or other audio alarm other than the secondsignal is being output.Warning Announcement indicator is on or
359. APPENDIX This appendix focuses on hints on installation and connections of associated equipment to the FS-971 Series.TABLE OF CONTENTS9.1. Notes
369.1. Notes on Parallel Rack Installation 9.1.1. Securing racks installed side by side Two knock-out holes (ø12 mm) are provided on each side of the
24 VDC 400 mA (rated output) 10 inputs - Amplifier output level: 50 V, 70 V, 100 V (changeable)Line output level: 0 dBV (1 V)33 x 140 mm dynamic spea
389.2.2. Connections • Connecting the Monitor Panel to the Integrated Control Panel EP-0510 permits emergency broadcast to bemonitored at the specific
399.3. Connections to the PBX and Intercom Systems By connecting the PA system to the PBX and intercom system, paging calls can be made from the telep
41. SUPPLIED MANUALSThe following manuals are supplied with the emergency PA system. Read only the manuals that are suited for your purpose.Installati
409.4. Source Equipment Connections When using a timer to activate source equipment to play a time signal chime or broadcast commercialmessages, conne
419.5. Tables for Each Panel's Switch Settings Note: Each figure of switch shows the factory-preset position.9.5.1. Integrated Control Panel EP-
420123456789ABCDEFAddress switch4Always OFF324 V not output24 V outputEmergency 24 V2NormalEmergencyEmergency contact1Always OFFTest modeONOFFSW1 sett
439.5.6. Integrated Remote Control Panel EP-059RONOFF12 3 45 67 812345678ONSW20112340ONOFF12341123421234312344123451234612347123481234912341012341112
Printed in Japan133-12-581-4C
Control cable (4 pairs)Under 50 ΩUnder 50 ΩUnder 50 ΩUnder 50 ΩUnder 50 ΩUnder 50 Ω52. CONNECTIONS OF INTEGRATED REMOTE CONTROL UNIT RM-9712.1. Connec
62.2.2. Connections of multiple remote control unitsWhen connecting two or more remote control units, be sure to branch each cable at the main rack. R
Suitable zone numbersUnder 80 zones90 – 110 zones120 – 150 zone160 – 220 zones230 – 330 zones7110 zones1.2 A2.3. Remote Control Unit Numbers/Zone Numb
82.4. Connections of Multiple Remote Control Units• Wiring diagram of Integrated Remote Control Unit CHOthersRM BUS ( / )24 VDC ( / )REMOTE
93. CONNECTION OF REMOTE MICROPHONE RM-12003.1. Notes on Connections The maximum distance between the main rack and the RM-1200 is 800 m.Use cables wi
Comments to this Manuals