Toa N-8031SB User Manual download pdf

CN306

CN307

CN304

CN101

CN302

CN303

CN301

To CN303 To CN301

Hands-free

speaker

(accessory)

Hands-free

microphone

(accessory)

Note

Be sure to use the accessories.

2-pin removable terminal plug

(accessory,

factory-attached to the CN101)

CN101

Removable terminal plug

(accessory)

N-8031SB

Insert into the CN101's pin header.

Tighten

1 2

To N-8000EX/8010EX Exchange

16 lines

N-8031SB

[Connections]

5.1. Connection to the Exchange

Connect the CN101 terminal to the Exchange's

network connection terminal via the E-7000TB

Terminal Board.

For details, read the installation manual supplied

with the Exchange.

Cable

Bared end: 7 mm

Conductor diameter:

ø 0.4 – 1.6 mm (AWG14 – 26),

Solid or Stranded wire

Mini-clamp connector

(Supplied with the

Exchange)

Twisted pair cable

Conductor diameter:

ø 0.8 – 1.3 mm (AWG16 – 20),

Solid or Stranded wire

COM

CN306

Push down.

Cable

CN306

8 mm

[Connections]

5.2. External Dial Switch Connection

Connecting external switches such as

footswitches permits them to perform the

same operation as the dial keys "7," "8,"

"9," and "C".

An electrical current of 1 mA flows through

each contact.

Note

The cable length from the external switch

should not exceed 3 m.

Connect a keyboard of

which circuit

configuration is as

shown in the figure.

An electrical current of

1 mA flows through

each contact.

5.3. Dial Key Connection

CN307

Note

For the CN307 connection,

use the PHR-10 connector

manufactured by J.S.T.

Mfg. Co., Ltd. or equivalent.

FUNCTION

RESP.

CALL

HOLD

REDIAL

PTT C

TRANSFER

10987654321

5.5. Status Indicator (LED) Connection

(Internal circuit)

1 kΩ

CN304

Status indicator (LED)

Control IC

TTL level output

+5 V DC

CN302

RS-191 rear

Ferrite clamp

(accessory)

Handset cable

5.4. RS-191 Connection

Socket

Note

Though the socket on the PC

board is faced inside, you can

insert the handset jumper into

the socket from the side.

Connecting the RS-191 Option Handset to the

N-8031SB permits handset conversation.

Note

Run the cables along

the ferrite groove,

and clamp them.

Handset jumper

(accessory,

factory-attached

to the CN302)

Use an LED with high brightness.

Note

For the CN304 connection, use the XHP-2 connector

manufactured by J.S.T. Mfg. Co., Ltd. or equivalent.

INSTALLATION MANUAL

MASTER STATION BOARD N-8031SB

1. GENERAL DESCRIPTION

The N-8031SB is a printed circuit board unit for the N-8031MS

Flush-Mount Hands-Free Master Station. You can make the

master station suitable for applications using the N-8031SB in

combination with the operation panel section to be prepared

separately.

3. SPECIFICATIONS

2. DIMENSIONAL DIAGRAM

Use the N-8000 software* to perform settings. Set up the same

items as performed to the N-8031MS since the N-8031SB is

handled as the N-8031MS on the software.

Key and status indicator operations are exactly the same as

those of the N-8031MS.

For settings, functions, and operations, read the descriptions

about the N-8031MS in the N-8000 Series instruction manual*.

* Included in the CD supplied with the N-8000EX/8010EX

Exchange.

4.1. Installation Precautions

• To prevent a malfunction or breakdown due to static electricity,

be sure to use a metal case or metal panel, and screw the board

at the indicated hole, so that the board is electrically conducted

to the case or panel.

4. MOUNTING TO A METAL CASE OR PANEL

• Cover the whole board with a case when installing.

4.2. Speaker and Microphone Installation

• To prevent acoustic feedback, attach the speaker and

microphone closely to the panel and position them at least 16 cm

away from each other's center as shown below.

133-06-273-9A

[Side] [Hands-free

speaker]

[Hands-free

microphone]

2.1. N-8031SB 2.2. Accessory

[Front

(Component side)]

Unit: mm

CN101

CN304

CN302

CN303

CN301

CN306

CN307

20.6

Mounting hole

6-ø3.5

8.5

521157

185

1.6

ø57

ø9

200

100

N-8031SB

Board fixing screw

Metal case or metal panel

Case or panel

16 cm or more

Microphone

Speaker

• Speaker opening ratio should be 36% (Example: ø4 mm x 61

holes) as a guide.

• Keep the board from coming in contact with the speaker to avoid

short-circuit between them.

• Make a microphone opening with the microphone rubber's inside

diameter (ø4.5 mm), and position the microphone in the way

that its center comes to the opening center.

• Never install them as shown below. Doing so may cause the

speaker sound to enter the microphone.

Case or panel

Microphone

Speaker

Microphone

Sound enters

the microphone.

Sound enters the microphone.

Speaker

5. CONNECTIONS

48 V DC (supplied from the N-8000EX/8010EX

IP Intercom Exchange)

1.8 W (rated), 2.4 W (max.)

Non-polar one pair stranded wire system

2-wire 160 kbps echo canceller transmission system

Under 0 dB*

Hands-free conversation

(Handset conversation can be established in

conjunction with the RS-191.)

300 – 7,000 Hz

Max. 1,500 m

(ø 0.65 mm, Loop resistance 170 Ω or less)

Speaker (accessory):

5.7 cm cone-type, 0.6 W, 8 Ω

Microphone (accessory):

Omni-directional electret condenser microphone

Pin header (2 pins)

Power Source

Power Consumption

Wiring Method

Transmission System

Signal Level

Speech Method

Audio Frequency Range

Transmission Range

Hands-Free

Line Connection

Terminal

Solderless connector (2 pins, male),

voltage: 5 V, maximum load current: 5 mA

Solderless connector (10 pins, male),

open voltage: 3.3 V DC, short-circuit current: 1 mA,

screwless connector (5 pins)

No-voltage make contact input, open voltage:

5 V DC, screwless connector (5 pins)

0°C to +40°C

Under 90% RH (no condensation)

70 (w) x 185 (h) x 20.6 (d) mm

205 g (including accessories)

Removable terminal plug (2 pins, preinstalled on

the unit) ... 1, Handset jumper (8 pins, preinstalled

on the unit) ... 1, Ferrite clamp ... 1, Hands-free

speaker (with connection cord) ... 1, Hands-free

microphone (with connection cord) ... 1

Status Indicator LED

Connecting Terminal

Dial Input

External Dial Input

Operating Temperature

Operating Humidity

Dimensions

Weight

Accessories

* 0 dB = 1 V

Note: The design and specifications are subject to change without notice for improvement.

MASTER STATION BOARD N-8031SB 1

Summary of Contents

Page 1 - MASTER STATION BOARD N-8031SB

CN306CN307CN304CN101CN302CN303CN301To CN303 To CN301Hands-freespeaker(accessory)Hands-freemicrophone(accessory)NoteBe sure to use the accessories.2-pi

Comments to this Manuals

No comments

Toa N-8031SB User Manual

Browse online or download User Manual for Equipment Toa N-8031SB. Toa N-8031SB User Manual [it] [de] [en] [fr]

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Toa N-8031SB