Toa HY-CL20B User Manual download pdf

4.2. HY-CL20B

Fixing bolt

(supplied with the speaker)

Fixing bolt

(supplied with the speaker)

Speaker system

F-2000 series

Speaker system

F-1000 series

Speaker bracket

(supplied with the speaker)

Speaker bracket

(supplied with the speaker)

Screw M5 x 20

(supplied with the speaker)

Screw M5 x 20

(supplied with the speaker)

• HY-CL20B

• HY-CL10B

Joint bracket (supplied with the speaker)

Accessory screw M5 x 10

Suspension wire

Note

Use the outer 4 holes

for wire connections.

Suspension wire

Note

Use the outer 4 holes

for wire connections.

Cluster bracket HY-CL10B

Cluster bracket HY-CL20B

The figure at left

shows the screw

mounting positions

for the F-1300

series.

Mount all 4 speakers to the cluster bracket before suspending

them.

If conditions require that the cluster bracket be suspended first,

take special care during assembly owing to weight balance

instability until all 4 speakers have been mounted.

Tip

The wall bracket supplied with each speaker is not used.

Step 1.

Attach the speaker bracket to the rear of each of the 4

speaker cabinets. Use the screws supplied with the speaker.

(HY-CL10B: 2 pieces x 4; HY-CL20B: 4 pieces x 4)

Note

Mount the bracket so that the speaker is suspended in a

vertical orientation.

Step 2.

Attach a joint bracket (4 brackets in total) to each of the 4

cluster bracket sections using the 16 screws supplied with

the cluster bracket.

Note

Before starting the work, ensure that all the screws used

for assembling the cluster bracket are firmly tightened.

Step 3.

Mount the 4 speakers to the joint brackets.

Insert the speaker bracket into the joint bracket and put the

fixing bolt through the joint bracket.

Adjust each speaker's vertical orientation, then tighten the

fixing bolt.

The speaker angle can be adjusted in 7.5º steps within the

range as follows.

F-1000/2000 series: 15º to 45º downward

F-1300 series: 15º to 30º downward

Step 4. Lift the speaker cluster up to the installation position using

a suspension wire.

Step 5. Connect the speaker cables to the speaker input

terminals. For connections, refer to the instruction manual

enclosed with the speaker.

INSTALLATION MANUAL

CLUSTER BRACKET HY-CL10B

HY-CL20B

30°

15°

Speaker bracket

[F-1000/2000 series: 15° to 45° downward]

[F-1300 series: 15° to 30° downward]

Joint bracket

45°

30°

15°

Refer to the figures below for the positional relationship

between the speaker bracket's "groove" and the joint

bracket's "indentation."

Note

The mating surfaces of the speaker bracket and joint

bracket are designed to interlock.

Ensure that both parts are securely engaged with each

other after mounting is complete.

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

1. SAFETY PRECAUTIONS

Indicates a potentially hazardous situation which, if

mishandled, could result in death or serious personal injury.

WARNING

• Refer all installation work to the dealer from whom the speaker

was purchased. Installation for flying requires extensive technical

knowledge and experience. The speaker may fall off if incorrectly

installed, resulting in possible personal injury.

• Flying Precautions

Be sure to follow the instructions below. Otherwise, the

suspension wires or belts may be off or snap and the speaker

may fall off, causing personal injury.

· Check to confirm that the suspension wires and belts are

strong enough to withstand the load.

· The connectors of the suspension wires and belts must be

securely linked with those of the load.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the speaker falling down and causing personal injury and/or

property damage.

• Since the unit is designed for indoor use, do not install it

outdoors. If installed outdoors, the aging of parts causes the

speaker to fall off, resulting in personal injury.

• Owing to the speaker's size and weight, be sure that at least two

persons are available to install the unit. Failure to do so could

result in personal injury.

• Do not use other methods than specified to mount the unit.

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the ceiling's structure

and composition. Failure to do so may cause the speaker to fall,

resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the unit has no

loose joints after installation to prevent accidents that could

result in personal injury.

• Use the specified speaker in combination. Doing otherwise may

cause the speaker to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

The unit can be damaged by excessive vibration, potentially

causing the speaker to fall, which could result in personal injury.

• Do not use anti-rust lubricant. If it contacts resin or rubber parts,

they could deteriorate and cause the unit to fall, possibly

resulting in personal injury.

Indicates a potentially hazardous situation which, if

mishandled, could result in moderate or minor personal

injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or

property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the unit that could cause the unit to fall, possibly causing

personal injury.

The HY-CL10B Cluster

Bracket allows a total of 4 F-

1000/1300 Series speaker

systems to be suspended

from a ceiling in a single

multi-directional cluster.

The HY-CL20B Cluster

Bracket is used for cluster

ceiling suspension of 4 F-

2000 Series speakers.

2. GENERAL DESCRIPTION

[Finished assembling diagram]

4. SPECIFICATIONS

Note:

The design and specifications are subject to change without

notice for improvement.

F-2000B, F-2000BT, F-2000W, F-2000WT

Steel plate, black, paint

904 (w) x 395 (h) x 904 (d) mm

(Maximum dimensions when the installed

4 speakers face 37.5° downward)

27.4 kg (When 4 F-2000Bs/2000Ws are

clustered)

30 kg (When 4 F-2000BTs/2000WTs are

clustered)

Machine screw M5 x 10 with washers

... 16

Applicable Speaker

Finish

Dimensions

Weight

Accessories

4.1. HY-CL10B

F-1000B, F-1000BT, F-1000W, F-1000WT,

F-1300B, F-1300BT, F-1300W, F-1300WT

Steel plate, black, paint

492 (w) x 214 (h) x 492 (d) mm

(Maximum dimensions when the installed 4

F-1000 series speakers face 30° downward)

568 (w) x 263 (h) x 568 (d) mm

(Maximum dimensions when the installed 4

F-1300 series speakers face 30° downward)

7.3 kg (When 4 F-1000Bs/1000Ws are

clustered)

8.1 kg (When 4 F-1000BTs/1000WTs are

clustered)

12.5 kg (When 4 F-1300Bs/1300Ws are

clustered)

14.3 kg (When 4 F-1300BTs/1300WTs are

clustered)

Machine screw M5 x 10 with washers

... 16

Applicable Speaker

Finish

Dimensions

Weight

Accessories

5. INSTALLATION

533-06-150-7A

URL: http://www.toa.jp/

CLUSTER BRACKET HY-CL10B 1
HY-CL20B 1

Summary of Contents

Page 1 - HY-CL20B

4.2. HY-CL20B3311Fixing bolt(supplied with the speaker)Fixing bolt(supplied with the speaker)Speaker system F-2000 seriesSpeaker system F-1000 seriesS

Related models: HY-CL10B

Comments to this Manuals

No comments

Toa HY-CL20B User Manual

Browse online or download User Manual for Acoustics Toa HY-CL20B. Toa HY-CL20B User Manual [pl] [en] [de]

Summary of Contents

Related models: HY-CL10B

Comments to this Manuals

Related products and manuals for Acoustics Toa HY-CL20B