Toa VM-3000 Series User Manual Page 108
- Page / 149
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
108
Recommended ferrule terminals for power supply cables
(made by Phoenix Contact)
Crimping tool: CRIMPFOX UD6-4 (made by Phoenix Contact)
Wiring procedures
Procedures below are for the removable terminal plug with fixing screws.
Step 1. Loosen the terminal screw and insert the
cable lead.
Step 2. Tighten the screw.
Pull on the cable lead to ensure it is securely
connected.
If the lead pulls out, loosen the screw and
follow the above procedures again.
Step 3. Insert the terminal plug into the corresponding
terminal block in the unit's rear panel.
Note
Do not reverse Steps 1 – 2 and 3 above.
Force is applied to the connected receptacle pins
while tightening the terminal screw and they may be
damaged, resulting in bad connector contact.
Solid cable and stranded cable
Shielded cable
7 mm*
7 mm*
15 mm
1
1
2
3
To tighten To loosen
Removable terminal plug
(accessory)
Terminal screw
Screwdriver
Cable sheath to trim
Insulation sleeve
Contact section
Insulation sleeve
Contact section
a
l
2
a
1
a
2
l
1
l
2
l
1
bb
Model Number a l
1
l
2
AI 0,34-8 TQ
AI 0,5-8 WH
2 mm
2.5 mm
12.5 mm
14 mm
8 mm
8 mm
b
0.8 mm
1.1 mm
Model Number a
1
l
1
l
2
AI 1,5-8 BK
AI-TWIN 2 x 1,5-8 BK 6.6 mm
a
2
3.6 mm
14 mm
16 mm2.3 mm
8 mm
8 mm
a
3.4 mm
b
1.8 mm
* Expose 8 mm or more when using the
above ferrule terminal, and cut off an extra
conductor protruding from the sleeve.
14. CONNECTIONS
14.1. Removable Terminal Plug Connection
Notes
• Do not use a micro screwdriver. Sufficient torque is not given to the screws when tightening them, and
connections may not be secured.
• Avoid soldering stranded or shielded cable, as contact resistance may increase when the cable is tightened
and the solder is crushed, possibly resulting in an excessive rise in joint temperatures.
• When connecting 2 cables or a shielded cable to a single terminal,
use a ferrule terminal with an insulation sleeve to crimp the cables
because such cable conductors could become loose.
Recommended ferrule terminals for signal cables
(made by Phoenix Contact)
- VM-3000 Series 1
- TABLE OF CONTENTS 2
- 13. INSTALLATION 4
- 1. GENERAL DESCRIPTION 6
- 2. FEATURES 6
- 3. SYSTEM CONFIGURATION 7
- 3.2. System Example 2 8
- [System outline] 8
- 3.3. System Example 3 9
- 4. NOMENCLATURE AND FUNCTIONS 10
- VM-3240VA and VM-3360VA 13
- VM-3240E and VM-3360E 13
- Not used 13
- [Top] [Side] 16
- [Bottom] 16
- [Top] [Side] 19
- [Rear][Side] 20
- 5. MAKING GENERAL BROADCASTS 25
- All-zone call key 26
- All-zone call indicator 26
- Output selector key 26
- Output indicator 26
- [VM-3240VA/3360VA] 26
- Zone selector key 28
- Zone indicator 28
- [RM-200M] 28
- Talk keyTalk indicator 28
- [VM-3240VA, VM-3360VA] 32
- [RM-300MF] 32
- ALL OUTPUT 1 – 6 33
- EMERGENCY 33
- Talk key 34
- MIC SP CPU 36
- 8. PRIORITY SETTINGS 45
- 9. CPU OFF FUNCTION 47
- Remote microphone 48
- 10. SURVEILLANCE 49
- Failure indicator 51
- [OK] key 54
- Failure 54
- Acknowledgment 54
- 10.6. LCD Failure Display 60
- Failure Location: Battery 62
- 11. SETTINGS 64
- 11.3. Configuration Settings 66
- Setting menu screen 67
- Password entry screen 67
- Password settings 68
- Date/time settings 69
- Network settings 70
- IP address settings 70
- Subnet mask settings 70
- Log transmission 72
- Transmission in 72
- Set data transmission 73
- Transmission from PC to 73
- VM-3360VA or VM-3240VA 73
- Transmission from VM-3360VA 73
- Transmission from 75
- VM-3360VA or VM-3240VA to PC 75
- Transmission 76
- 11.4. Information Settings 77
- VERS I NOVA 78
- 11.5. Audio Settings 79
- Bass settings 80
- Input 4 tone settings 80
- Treble settings 80
- BGM 1 volume adjustment 81
- Microphone-interlocked chime 81
- Automatic general message 83
- 11.6. Surveillance Settings 84
- 11.7. Inputs 1 – 3 Settings 85
- 11.8. BGM Settings 87
- 12.1. DIP Switch Functions 89
- 12.3. Compression Settings 90
- 12.2. Unit ID Number Settings 90
- Name label entry slit 100
- Name label A Name label B 102
- Shown in actual size 102
- Cutting guideline 102
- Name label C 102
- Power Amplifiers 104
- DRIVE PCB 105
- Rear panel 105
- 13.8. Rack Mounting 106
- Over 10 cmOver 10 cm 107
- Over 10 cm 107
- 14. CONNECTIONS 108
- VX-2000DS 109
- RM-200M Rear 115
- AD-246 AC Adapter or 115
- To AC power 115
- CTRL IN 1 122
- 87654321 126
- 14.8.1. Speaker connection 127
- 28 V 4.8 A 129
- DC POWER IN 129
- PA OUT (SP LINE) 129
- PA LINK VP-200VX 130
- VM-3240VA 133
- VM-3240E 133
- Lead-acid Battery 133
- DC POWER 134
- VX-200PS 134
- 15. VM-3000 CABLE USAGE TABLE 136
- [VP-2241/2421] 137
- [VX-2000DS] 137
- [VX-200PS] 137
- 16. SPECIFICATIONS 138
- URL: http://www.toa.jp/ 149
Related products and manuals for Receivers and Amplifiers Toa VM-3000 Series
(8 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 2.320 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals